CONDITION : NEW

 

This adjustable , made ​​of special aluminum alloy and anodized satin black .

Prepared for the installation of our LED license plate light (code ELT001 ) .

The kit provides all the screws, nuts and 2 brackets for aftermarket arrows with holes of 10mm .

This family of license plate consists of a number plate holder universal and attacks specific to your motorcycle made ​​of a special aluminum- magnesium.

This alloy has the characteristic to resist very well to continuous vibration. To further increase security, all the folds are made with a very large radius , so as not to enervate the sheet during the processing .

WARNING ! all the license plate will be delivered with the new model of support plate in aluminum - polycarbonate composite
Led license plate light and reflector support are not included in the kit and can be ordered separately.

Following numerous reports of violations attributed to our customers on the Italian territory for mounting the plate holder adjustable, are reflected on the important note to use in case of correct installation as determined by the Presidential Decree 16.12.1992 . 495 .

Assuming that they comply with the constraints established by points A , B, C, D , E, F , G, detailed in the article DPR 16.12.1992 . 495 . below, can not be applied Article .72 of the highway code as the system holder does not constitute the structural part of the frame.
For the structural parts of the vehicle , so all the parts where there is an approval code as chassis, engine, corrrispondenza is identified in the registration certificate of the vehicle.

This article should not , however, constitute justification on which to use if they are not complied with these installation criteria set forth above. Article 259

(DPR 16.12.1992 . 495 - rules to the new rules of the road )
(Art. 100 Code of the street)
How to install license plate
1 . The mounting shall be such that , as a result of their correct fixing, the plates have the following characteristics :
B. position of the rear license plate in width , except for the registration plates of trailers, agricultural trailers and towed machinery : the median vertical line of the plate may not be situated to the right of the median longitudinal plane of the vehicle and in every If , in the drawn vehicles , must be ensured a fair distance between the registration plate and repeater plate . The left lateral edge of the plate may not be more to the left of the vertical plane parallel to the longitudinal plane of symmetry of the vehicle and tangent to the place where the cross section of the vehicle , overall width, reaches its maximum size ;
B. position , meaning the width, the registration plates of trailers, agricultural trailers and towed machinery : such plates shall be placed near the right edge of the rear side of the vehicle, without going over the edge ;
C. position of the plate in relation to the longitudinal plane of symmetry of the vehicle: the plate is perpendicular or substantially perpendicular to the longitudinal plane of symmetry of the vehicle;
D. position of the rear license plate to the vertical: the plate is vertical with a tolerance of 5 ° . However , to the extent that the shape of the vehicle so requires, it may be inclined from the vertical by an angle not exceeding 30 ° , when the surface bearing the alphanumeric characters is facing upward and provided that the upper edge of the plate do not begin from the ground more than 1,20 m ; through an angle not greater than 15 ° when the surface bearing the registration number is pointing down , and provided that the upper edge of the plate from the ground cage is more than 1.20 m ;
E. height of the rear license plate to the ground : the height of the lower edge of the plate from the ground shall not be less than 0.30 m, and 0.20 m only for motorcycles , the height of the upper edge of the plate from the ground shall not be more than 1.20 m. However , if it is practically impossible to comply with this latter provision, the height may exceed 1.20 meters , but should be as close as possible to that limit as the constructional characteristics of the vehicle, and can not in any case exceed 2 m;
F. geometric visibility : the rear license plate must be visible in all the space between the four planes, viz : the two vertical planes passing through the two side edges of the plate and forming an outward angle of 30 ° with the longitudinal median plane of the vehicle, a plane passing through the upper edge of the plate and forming with the horizontal plane an angle of 15 ° upwards , a horizontal plane passing through the lower edge of the plate ( however, if the height of the upper edge of the plate from the ground is greater than 1.20 m , the latter plane shall form with the horizontal plane at an angle of 15 ° downward ) , G. determining the height of the plate from the ground : the heights in points d), e ) and f) shall be measured with the vehicle unladen . 2 . It is permissible to use frames holder provided that they are of opaque material and they hold the edge of the plate to a depth not exceeding 3 mm . It is prohibited to apply on the plate and on the heads of the screws materials having retroreflective properties . It is prohibited to apply any coating material on the plate even if transparent .